SAQA All qualifications and part qualifications registered on the National Qualifications Framework are public property. Thus the only payment that can be made for them is for service and reproduction. It is illegal to sell this material for profit. If the material is reproduced or quoted, the South African Qualifications Authority (SAQA) should be acknowledged as the source.
SOUTH AFRICAN QUALIFICATIONS AUTHORITY 
REGISTERED UNIT STANDARD THAT HAS PASSED THE END DATE: 

Joint Medium / High Voltage cables 
SAQA US ID UNIT STANDARD TITLE
113874  Joint Medium / High Voltage cables 
ORIGINATOR
SGB Electrical Engineering & Construction 
PRIMARY OR DELEGATED QUALITY ASSURANCE FUNCTIONARY
-  
FIELD SUBFIELD
Field 12 - Physical Planning and Construction Electrical Infrastructure Construction 
ABET BAND UNIT STANDARD TYPE PRE-2009 NQF LEVEL NQF LEVEL CREDITS
Undefined  Regular  Level 4  NQF Level 04  8 
REGISTRATION STATUS REGISTRATION START DATE REGISTRATION END DATE SAQA DECISION NUMBER
Passed the End Date -
Status was "Reregistered" 		 2007-04-03  2009-02-18  SAQA 0160/05 
LAST DATE FOR ENROLMENT LAST DATE FOR ACHIEVEMENT
2010-02-18   2013-02-18  

In all of the tables in this document, both the pre-2009 NQF Level and the NQF Level is shown. In the text (purpose statements, qualification rules, etc), any references to NQF Levels are to the pre-2009 levels unless specifically stated otherwise.  

This unit standard is replaced by: 
US ID Unit Standard Title Pre-2009 NQF Level NQF Level Credits Replacement Status
259189  Joint Medium Voltage cables  Level 4  NQF Level 04  8   

PURPOSE OF THE UNIT STANDARD 
This unit standard is for persons in the Electrical Engineering, Distribution and Construction environment.

A person credited with this unit standard will be capable of:
  • Jointing and testing of Medium and High Voltage cables according to statutory and manufacturer`s specifications.

    This unit standard will contribute to the full development of the learner within the electrical engineering, distribution and construction environment by providing recognition, further mobility and transportability within the field of Physical Planning and Construction. The skills, knowledge and understanding demonstrated within this unit standard are essential for social and economic transformation and upliftment within the electrical engineering, distribution and construction environment. 
    		•

    LEARNING ASSUMED TO BE IN PLACE AND RECOGNITION OF PRIOR LEARNING 
    The following knowledge, skills attitude and / or equivalent:
  • Use and knowledge of electrical testing instruments
  • Introduction to industry
  • Knowledge of electrical drawings
  • Knowledge of isolating and safety testing procedures 
    		•

    UNIT STANDARD RANGE 
  • Materials may include but are not limited to Medium and High Voltage cables, solid or stranded conductors, glands, lugs, ferrules, insulation, various metals and jointing kits.
  • Tests on High Voltage cables are limited to phasing, continuity, short circuit, earth resistance, open circuit and high resistance.
  • Statutory requirements include but are not limited to OSH Act, SABS, Authority requirements, manufacturers specifications and worksite procedures.
  • Specialised tools to be used for Medium / High Voltage cable joints may include but are not limited to pulse generator, injection test set, spike gun, Medium / High Voltage insulation tester, gas torch, hydraulic cable cutters / crimpers and special jointing kits as per jointing requirements.
  • Medium / High Voltage cables may include but are not limited to lead sheath (paper insulated), PVC, XPLE and PILC types. 
    		•

    Specific Outcomes and Assessment Criteria: 

    SPECIFIC OUTCOME 1 
    Plan to joint Medium / High Voltage cable. 

    ASSESSMENT CRITERIA     

    ASSESSMENT CRITERION 1 
    1. Task details are determined according to fault reports or instructions. 

    ASSESSMENT CRITERION 2 
    2. Appropriate drawings and documentation are acquired in accordance with job specifications. 

    ASSESSMENT CRITERION 3 
    3. Materials are selected according to job requirements. 

    ASSESSMENT CRITERION 4 
    4. Applicable test equipment is selected and checked for functionality. 

    ASSESSMENT CRITERION 5 
    5. Appropriate tools are selected according to job requirements. 

    ASSESSMENT CRITERION 6 
    6. Relevant parties are liased with and notified according to worksite procedures. 

    SPECIFIC OUTCOME 2 
    Prepare the Medium / High Voltage cable and work area. 

    ASSESSMENT CRITERIA     

    ASSESSMENT CRITERION 1 
    1. The correct cable is identified and selected according to drawings and reticulation diagrams. 

    ASSESSMENT CRITERION 2 
    2. Isolation of the circuit is confirmed and permit is obtained according to operating regulations for High Voltage systems and worksite procedures if required. 

    ASSESSMENT CRITERION 3 
    3. The cable is tested to establish exact work point where necessary. 

    ASSESSMENT CRITERION 4 
    4. Confirm that the cable to be worked on is at zero potential by spiking and made safe as per safety standards, procedures and work requirements. 

    ASSESSMENT CRITERION 5 
    5. Safety of work area is ensured according to statutory requirements and safe work procedures (barricading / shoring). 

    SPECIFIC OUTCOME 3 
    Joint Medium / High Voltage cable. 

    ASSESSMENT CRITERIA     

    ASSESSMENT CRITERION 1 
    1. Applicable tools and equipment are selected and used safely to meet the requirements of the job. 

    ASSESSMENT CRITERION 2 
    2. Cable ends are phased, discharged and prepared for jointing according to manufacturer specifications. 

    ASSESSMENT CRITERION 3 
    3. Cable cores are joined according to manufacturer specifications. 

    ASSESSMENT CRITERION 4 
    4. The cable joint is completed as per manufacturers specifications. 

    ASSESSMENT CRITERION 5 
    5. Insulation resistance / continuity / phasing and mechanical tests are carried out on cable / completed joint. 

    SPECIFIC OUTCOME 4 
    Complete the work task. 

    ASSESSMENT CRITERIA     

    ASSESSMENT CRITERION 1 
    1. The work permit is cleared according to operating regulations for High Voltage systems and worksite procedures if required. 

    ASSESSMENT CRITERION 2 
    2. Work area is restored in accordance with environmental legislation. 

    ASSESSMENT CRITERION 3 
    3. Applicable tools and equipment are cleaned and stored according to OHS Act requirements. 

    ASSESSMENT CRITERION 4 
    4. Documentation is completed and submitted according to data management procedures. 


    UNIT STANDARD ACCREDITATION AND MODERATION OPTIONS 
    1. Anyone assessing a learner against this unit standard must be registered as an assessor with the relevant ETQA.

    2. Any provider offering learning that will enable achievement of this unit standard must be accredited as a provider through the relevant ETQA.

    3. Moderation of assessment will be overseen by the relevant ETQA according to the moderation guidelines in the relevant qualification and the agreed ETQA procedures. 

    UNIT STANDARD ESSENTIAL EMBEDDED KNOWLEDGE 
    Knowledge that will help me understand and that I will be able to explain:
  • Terminology associated with testing equipment and materials.
  • Operating principles of testing equipment.
  • Relevant sections of statutory requirements.
  • General testing principles for cable and conductors.
  • Handling and application of applicable jointing kits.
  • Working principles of applicable equipment and components. 
    		•

    UNIT STANDARD DEVELOPMENTAL OUTCOME 
    N/A 

    UNIT STANDARD LINKAGES 
    N/A 


    Critical Cross-field Outcomes (CCFO): 

    UNIT STANDARD CCFO IDENTIFYING 
    Identify and solve problems. 

    UNIT STANDARD CCFO WORKING 
    Work effectively with others as a member of a team or group. 

    UNIT STANDARD CCFO COMMUNICATING 
    Communicate effectively by means of language skills, oral and / or written. 

    UNIT STANDARD ASSESSOR CRITERIA 
    N/A 

    UNIT STANDARD NOTES 
    This unit standard has been replaced by unit standard 259189, which is "Joint Medium Voltage cables", Level 4, 8 credits. 

    QUALIFICATIONS UTILISING THIS UNIT STANDARD: 
      ID QUALIFICATION TITLE PRE-2009 NQF LEVEL NQF LEVEL STATUS END DATE PRIMARY OR DELEGATED QA FUNCTIONARY
    Elective  48474   National Certificate: Electrical Engineering  Level 4  Level TBA: Pre-2009 was L4  Passed the End Date -
    Status was "Reregistered"     		 2009-02-18  Was EWSETA until Last Date for Achievement 


    PROVIDERS CURRENTLY ACCREDITED TO OFFER THIS UNIT STANDARD: 
    This information shows the current accreditations (i.e. those not past their accreditation end dates), and is the most complete record available to SAQA as of today. Some Primary or Delegated Quality Assurance Functionaries have a lag in their recording systems for provider accreditation, in turn leading to a lag in notifying SAQA of all the providers that they have accredited to offer qualifications and unit standards, as well as any extensions to accreditation end dates. The relevant Primary or Delegated Quality Assurance Functionary should be notified if a record appears to be missing from here.
     
    NONE 


    All qualifications and part qualifications registered on the National Qualifications Framework are public property. Thus the only payment that can be made for them is for service and reproduction. It is illegal to sell this material for profit. If the material is reproduced or quoted, the South African Qualifications Authority (SAQA) should be acknowledged as the source.